U-Boot 1.1.3 (Jul 29 2013 - 10:29:51)
Board: Ralink APS
oC DRAM: 32 MB
relocate_code Pointer at: 81fb4000
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 42
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.0.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Jul 29 2013 Time:10:29:51
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
\0x08\0x08\0x08 4
\0x08\0x08\0x08 3
\0x08\0x08\0x08 2
\0x08\0x08\0x08 1
\0x08\0x08\0x08 0
3: System Boot system code via Flash.
## Booti
ng image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3830574 Bytes = 3.7 MB
Load Address: 80000000
Entry Point: 802cf000
raspi_read: from:50040 len:3a732e
..........................
................................. Verifying Checksum ...
OK
Uncompressing Kernel Image ...
OK
No initrd
## Transferring control to Linux (at address 802cf
000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.21 (ray@asiarf-Aspire-S3) (gcc version 3.4.2) #334 Tue Nov 26 14:28:26 CST 2013
The CPU frequency set to 360 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists. Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 40808008, status = 11000000
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 000000c8(200)
CPU frequency 0.05 MHz
Using 0.050 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26652k/32768k available (2198k kernel code, 6116k reserved, 673k data, 2856k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol fa
mily 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
deice id : c2 20 17 c2 20 (2017c220)
MX25L6405D(c2 2017c220) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x00000000-0x00800000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
Time: MIPS clocksource has been installed.
0x00040000-0x00050000 : "Factory"
0x00050000-0x01000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=1048576,origSize=12314112
LZMA initramfs by Ming-Ching Tiew .............
............................................................
............................................................
.......................................................RT3xxx E
HCI/OHCI init.
fuse init (API version 7.8)
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.9 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
rdm_major = 253
Ralink APSoC Ethernet Driver Initilization. v2.1 256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43305077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.1
block2mtd: version $Revision: 1.1.1.1 $
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci
rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
Freeing unused kernel memory: 2856k freed
init started: BusyB
ox v1.12.1 (2013-10-15 14:30Algorithmics/MIPS FPU Emulator v1.5
:14 CST)
starting pid 629, tty '': '/etc_ro/rcS'
devpts: called with bogus options
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
\0x09 =System Architecture Department=
starting pid 638, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2013-10-15 14:30:14 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# ralink_gpio: sending a SIGUSR1 to process 633
internet.sh
Password for 'admin' changed
rmmod: ralink_wdt: No such file or directory
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found
##### disable 1st wireless interface #####
rmmod: rt2860v2_a
p_net: No such file or directory
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_ap_util: No such file or directory
rt2860v2_ap: module license 'unspecified' taints kernel.
==
= pAd = c0002000, size = 805120 ===
<-- --="" -="" -f="" -t="" 00="" 01="" 0="" 0x0000000c="" 0x1300="00064380" 0x43305077="" 0x8913="" 0x8914="" 1.="" 1="" 2.="" 20mhz.l="" 2="" 3.="" 3100="" 3900="" 8021q.ko:="" 8021q:="" :="" a0493000="" address="" argument="" assign="" bbp="" be="" blinks="" br0:="" brctl:="" bridge="" bssid="00:0c:43:30:50:90" can="" cannot="" change="" changed="" config="" desc="" detected="" dev_set_promisc="" device="" directory="" do="" does="" done.="" entered="" entering="" error="" esw="" etc="" eth2.1:="" eth2.1="" eth2="" exist="" failed:="" file="" filter="" for="" forwarding="" found="" ifconfig:="" initialize="" insmod:="" insmod="" inva="" invalid="" ioctl="" iptable="" iptables="" is="" kernel="" key1str="" key2str="" key3str="" key4str="" key="" killall:="" killed="" learning="" led="13," length="" lid="" link="" mac_adrh="" mac_adrl="" main="" mangle="" master="" mcs="" mode="" module="" need="" needs="" nf_con="" nf_conntrack_proto_gre:="" nf_nat_pptp:="" nf_nat_proto_gre:="" no="" not="" ntrack_pptp:="" off="4000," offset="70," on="1," or="" partition="" perhaps="" ph="" phy="" phy_rx_ring="" phy_tx_ring="0x016f2000," port="" process="" promiscuous="" propagating="" r4="" ra0="" radvd.conf="" ralink="" reg="" rem:="" remove="" requested="" reset="1," rm:="" rmmod:="" rt28xx_init="" rt305x_esw:="" rtmpallocadapterblock="" rtmpalloctxrxringmemory="" rx="" rx_ring0="0xa16f3000" s="" set:="" set="ff" size="2048" stat="" state="" status="" such="" switch="" sync="" t="" table="" time="4000" to="" topology="" tx_ring="0xa16f2000" type="" udhcpd:="" uity="" upgraded.="" us="" v1.3.5:="" value="ffff506f" vconfig:="" vlan="" write="" x_esw:="" y="" you="" your="">/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter 1>/dev/null 2>&1
iptables -F web_filter 1>/dev/null 2>&1
iptables -D FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -F malicious_filter 1>/dev/null 2>&1
iptables -D INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -F malicious_input_filter 1>/dev/null 2>&1
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_input_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_filter -p tcp --syn -j synflood_filter 1>/dev/null 2>&1
iptables -t filter -A INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_input_filter -p tcp --syn -j synflood_input_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
iptables -A malicious_input_filter -i eth2.2 -p tcp --dport 80 -j DROP
/bin/super_dmz -f
sh: /bin/super_dmz: not found
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward 1>/dev/null 2>&1; iptabl
es -t nat -X port_forward 1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ 1>/dev/null 2>&1
cat /proc/sys/net/netfilter/nf_conntrack_udp_timeout > /var/.udpbackup
echo 0 > /proc/sys/net/netfilter/nf_conntrack_udp_timeout
cat /var/.udpbackup > /proc/sys/net/netfilter/nf_conntrack_udp_timeout; rm -f /var/.udpbackup
cat /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established > /var/.tcpbackup
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established
cat /var/.tcpbackup > /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established; rm -f /var/.tcpbackup
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
ntp.sh
ddns.sh
kill -9 `cat /var/run/wscd.pid.ra0`
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
route delete 239.255.255.250 1>/dev/null 2>&1
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null
2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
echo 0 > /proc/sys/net/ipv6/conf/all/forwarding
webs: Listening for HTTP requests at address 10.10.10.254
fetchSmbConfig: No such file or directory
killall -q -USR1 udhcpd
No comments:
Post a Comment